Pneumatics Training

Performance focused training and consultancy

HOME

ABOUT IPS INTERNATIONAL

TRAINING COURSES

ENGINEERING

Electrical training

Mechanical Maintenance

•	Hydraulics Training

•	Pneumatics Training

•	Abrasive Wheels Training

•	Control and Instrumentation

•	Welding training

•	ENGINEERING COURSE DATES 2010

17th EDITION WIRING REGULATIONS

MANAGEMENT

•	HEALTH AND SAFETY

COMPUTER AND IT TRAINING

•	HEALTH AND SOCIAL CARE TRAINING

NATIONAL VOCATIONAL QUALIFICATIONS

IPS International
Northbank House
Sir Thomas Longley Road
Medway City Estate
Rochester
Kent ME2 4DU
Tel: 01634 298800

IPS International Ltd.
54-56 Castle Street,
Dover, Kent
CT16 1PJ
Tel: 01304 228180

theoffice@ips-international.com

IPS International Ltd is registered in England number 3368622, with its registered office at the Rochester address above.

Pneumatics Training

Technicians that complete the IPS Pneumatics training course are able to competently,

Recognise fluid power components and understand their use
Read schematics and understand the symbols used and their function
Use appropriate fault finding techniques to ascertain the nature of a fault - flow, pressure, directional, actuator or machine related
Assemble and test circuits that make use of a variety of standard pneumatic & electro-pneumatic control valves
Assemble and test circuits that also incorporate a variety of pneumatic LOGIC valves
Use appropriate fault finding techniques to diagnose faults in a pneumatics power system.

Competency example:

For a pneumatic system, technicians will know how and why a logic “AND” valve should be used in a circuit.

Pneumatics training course contents:

1) PNEUMATIC PRINCIPLES
    a) Compressed Air, Gas Laws, Water Condensation, Pressure Dew Point

2) PNEUMATIC SYSTEMS
    a) Pneumatic circuit symbols
    b) Single-stage and Multi-stage compressor units
    c) Air receivers
    d) Safe start-up and inspection procedures
    e) Distribution Systems

3) AIR LINE PIPING AND FITTINGS
    a) Pressure Regulators, Air Flow Regulators,
    b) Air line filters and lubricators, Moisture Separators
    c) Nylon pipework application - connection, fittings

4) AIR CYLINDERS
    a) Single-acting cylinders
    b) Double-acting cylinders
    c) Cylinder seals
    d) Soft seating techniques5)

5) CONTROL
    a) Flow regulation
    b) Direction control valves, standards
    c) Types of valve, ports, spools, Pilot, solenoid operation
    d) Circuit symbols, Circuit presentation, and documentation
    e) Fault finding and problem analysis

6) COMPONENTS
    a) Pneumatic sensors
    b) Logic and time delay units
    c) Rotary actuators
    d) Rodless actuators

Pneumatics Training Course Practical Exercises
Function & operation of pressure controls, flow controls, directional controls, logic valves, timers, actuators (linear & rotary).
Assembling & Testing Circuits, Simple sequence, complex sequence, “AND”/”OR”, interlock.Fault Location & Diagnosis – component (flow, pressure or direction).
Schematics – ISO1219, CETOP, study & interpretation

At each stage trainees undertake a practical task designed to reinforce a practical topic and add real relevance to the training.

SEE THE COURSE DATES FOR THIS COURSE - COURSE DATES


17TH EDITION UPDATE COURSE Begins: 03/09/2010 Duration: 1 day Cost: £250 + VAT * * * INTRODUCTION TO MS WORD Begins: 07/09/2010 Duration: 1 day Cost: £95 + VAT * * * 2392 FUNDAMENTAL INSPECTION & TESTING Begins: 13/09/2010 Duration: 4 days Cost: £465 + VAT * * * INTRODUCTION TO MS POWERPOINT Begins: 15/09/2010 Duration: 1 day Cost: £95 + VAT * * * OPEN ELECTRICAL MODULE 1 Begins: 21/09/2010 Duration: 3 days Cost: £465 + VAT * * * INTRODUCTION TO MS OUTLOOK Begins: 23/09/2010 Duration: 1 day Cost: £95 + VAT * * * MIG WELDING Begins: 29/09/2010 Duration: 2 days Cost: £440 + VAT * * * PAT TESTING Begins: 04/10/2010 Duration: 1 day Cost: £245 + VAT * * * INTRODUCTION TO MS ACCESS Begins: 05/10/2010 Duration: 1 day Cost: £95 + VAT * * * CITY & GUILDS 7300-01 INTRODUCTION TO TRAINER SKILLS AWARD Begins: 05/10/2010 Duration: 2 days Cost: £275 plus VAT plus registration £46.60 * * * MS EXCEL EXPERT Begins: 07/10/2010 Duration: 1 day Cost: £95 + VAT * * * ABRASIVE WHEELS Begins: 12/10/2010 Duration: 1 day Cost: £215 + VAT * * * OPEN ELECTRICAL MODULE 2 Begins: 12/10/2010 Duration: 3 days Cost: £645 + VAT * * * MS WORD ADVANCED Begins: 13/10/2010 Duration: 1 day Cost: £95 + VAT * * * MMA WELDING Begins: 25/10/2010 Duration: 5 days Cost: £1100 + VAT * * * 17TH EDITION UPDATE COURSE Begins: 29/10/2010 Duration: 1 day Cost: £250 + VAT * * * INTRODUCTION TO MS EXCEL Begins: 02/11/2010 Duration: 1 day Cost: £95 + VAT * * * IOSH Begins: 02/11/2010 Duration: 4 days Cost: £475 + VAT * * * OPEN ELECTRICAL MODULE 1 Begins: 02/11/2010 Duration: 3 days Cost: £645 + VAT * * * BEARINGS Begins: 03/11/2010 Duration: 2 days Cost: £425 + VAT * * * INTRODUCTION TO MS PUBLISHER Begins: 09/11/2010 Duration: 1 day Cost: £95 + VAT * * * 17TH EDITION FULL COURSE Begins: 16/11/2010 Duration: 4 days Cost: £425 + VAT * * * OPEN ELECTRICAL MODULE 3 Begins: 16/11/2010 Duration: 3 days Cost: £645 + VAT * * * MS ACCESS ADVANCED Begins: 17/11/2010 Duration: 1 day Cost: £95 + VAT * * * TIG WELDING Begins: 17/11/2010 Duration: 3 days Cost: £660 + VAT * * * COUPLINGS Begins: 17/11/2010 Duration: 2 days Cost: £430 + VAT * * *